Home > General > Himem.sys


If you receive this message, you should have your computer's memory checked by a qualified computer hardware technician. Privacy policy About Wikipedia Disclaimers Contact Wikipedia Developers Cookie statement Mobile view Skip to Main Content Search Help Tips Dictionary History Forums Contact You are here: Dictionary > H - Definitions DEVICEHIGH=C:\Windows\COMMAND\ANSI.SYS The ansi.sys line is a driver for DOS to allow you to have different colors and sizes and special characters at the DOS prompt. To do this, the dos=high line must follow the activation of HIMEM.SYS (see below).

PCMag Digital Group PC, PC Magazine and PC PCMag.com are among the federally registered trademarks of Ziff Davis, LLC and may not be used by third parties without explicit permission. Make sure you have the below three lines at the beginning of your config.sys file. Versions of Microsoft Windows after Windows 98 only utilized the memory manager included with Windows. See DOS Dos and DOS EMM386.EXE. < Back to List ∧Top A B C D E F G H I J K L M N O P Q R S T https://en.wikipedia.org/wiki/HIMEM.SYS

FCBS= Line used to specify the number of file control blocks for file sharing. You can specify a value from 0 to 63. The value for xxxx can be any of the codes or their equivalent numbers listed in the following table. In Windows 9x, there is also a command-line loadable version of HIMEM.SYS called XMSMMGR.EXE.

This device driver is of particular importance because various versions of Microsoft Windows that ran on top of the DOS operating system required HIMEM.SYS to be loaded to be able to To free up more conventional memory, HIMEM.SYS also allows part of DOS to be loaded into the first 64K block of extended memory known as the high memory area (HMA). The HIMEM.SYS command line must come before any commands that start applications or device drivers that use extended memory; for example, the HIMEM.SYS command line must come before the EMM386.EXE command You will find the updated version (internet) here and the version described in this manual page here.

Although you can disable the memory test and load HIMEM by using the /TESTMEM:OFF switch, it's not advisable to do so until you have had the memory checked by a technician. All other reproduction is strictly prohibited without permission from the publisher. //Most Popular Articles 32 Hidden Chrome Features That Will Make Your Life Easier How to Fix the Most Annoying Things If this line is not present, Windows 3.x will not load. The /HMAMIN option is not required; the default value is zero.

THESE COPYRIGHTED DEFINITIONS ARE FOR PERSONAL USE ONLY. However, keep in mind that the /D:123 must be exactly the same in config.sys and autoexec.bat. HIMEM's memory test is more thorough than the standard power-up memory test performed by most computers. DEVICE=C:\Windows\HIMEM.SYS DOS=HIGH,UMB DEVICE=C:\Windows\EMM386.EXE NOEMS By placing the DOS=HIGH,UMB on the second line, this can, in some cases, save memory because it is loading DOS into upper memory before loading the memory

Forum If your question is not listed on this page, try our online forum. A220 = port address "220", I5 = IRQ 5, D1 = DMA 1 usually being the settings for most sound cards. Was this page useful? How to edit the files Remarking information Getting additional memory Autoexec.bat layout Config.sys layout Information about batch files Technical support How to edit the files The auotexec.bat and the config.sys are

The STACKS statement has a range of 8-64, 32-512. Additionally, the first and third lines cannot be loaded into high memory because these lines are the memory managers. HIMEM tests the memory by writing and reading data to each memory address and checking for differences in the data. Default memory allocation Only one program at a time can use the high memory area (HMA).

LH C:\MOUSE\MOUSE.EXE Loads the mouse driver into memory. HIMEM.SYS From Wikipedia, the free encyclopedia Jump to: navigation, search This article does not cite any sources. To ensure the most efficient use of your system's high memory area, set /HMAMIN=m to the amount of memory required by the program that uses the most HMA memory. Please help improve this article by adding citations to reliable sources.

More Info MS KB109845 Updated: 3 July 2007 Tags:himem-sys, memory-testing Category: MS DOS/Tips Leave a Reply Cancel reply Your email address will not be published. Computer memory help and support. If you receive this message, you should have your computer's memory checked by a qualified computer hardware technician.

CH000007 Getting the mouse to work in MS-DOS CH000210 As the computer boots I receive bad command or file name.

However, with newer versions of Windows are no longer needed. Currently, systems that require this option include Acer 1100, Wyse, and IBM 7552. Disabling the memory test will shorten the startup process. (The default setting is /TESTMEM:ON.) /VERBOSE Directs HIMEM to display status and error messages while loading. It is not recommended this line be used unless you are using Windows 3.11 or earlier since later version of Windows will ignore this line.

Only one application can use the HMA at a time; HIMEM allocates the HMA to the first application that meets the memory-use requirements set by this option. For better operation, change the line in CONFIG.SYS to reference the more current HIMEM.SYS in the DOS directory, rather than the Windows directory. unused Command: himem HIMEM is the High Memory Manager. If the data HIMEM reads from an address differs from the data it just wrote to that address, then the memory at that address is unreliable.

In special circumstances, this line was changed to STACKS=9,128. Load all your devices in your config.sys and autoexec.bat into high memory. To ensure the most efficient use of your system's high memory area, set /HMAMIN=m to the amount of memory required by the program that uses the most HMA memory. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.

Constant Contact Review Join.Me Review LiquidPlanner Review Microsoft Office 2016 Review Microsoft Office For Mac Review Microsoft Office 365 Review Vivantio Pro Review Wrike Review Zoho Projects Review Cameras & Photo/Video The /D:123 represents the name of the driver, which in this case is named 123, however, can be named anything, usually MSCD0001. DOSKEY DOS command to load DOSKEY into memory so when in DOS you can use it without having to load it. You can specify a value from 1 to 128; the default value is 32.

You might need to include the /MACHINE option if your computer is a type that HIMEM cannot detect and if HIMEM does not work properly on your system by using the Should only be used when programs require it, and today, is not used or required. DOS=HIGH,UMB Load DOS into high memory in an upper memory block. If they are different, the CD-ROM will not work in MS-DOS.